15140666 مضخة هيدروليكية رئيسية لفولفو A25F A40F A25G A40G

وصف المنتج:

الجزء: 15140666 مضخة هيدروليكية رئيسية لقلابات فولفو المفصلية A25F وA30F وA35F وA40F وA25G وA30G وA35G وA40G، مُدرجة في بيانات قطع الوكيل كمضخة هيدروليكية تشمل السلسلتين.

الدائرة: الهيدروليك الرئيسي للمعدات العاملة، وليس تشغيل مروحة التبريد.

يُورَّد على النحو التالي: بديل جديد بعلامة HTD، صناعة صينية. الحد الأدنى للطلب قطعة واحدة، صندوق خشبي، الإرسال خلال 5 إلى 8 أيام عمل.

الوصف

A pump that spans two hauler generations is genuinely useful for a fleet carrying both. It is also the sort of listing that gets stretched too far, so here is what the evidence supports and where it stops.

قابلية التطبيق والأدلة

Volvo A25F, A30F, A35F, A40F and the matching G-series A25G, A30G, A35G and A40G articulated haulers, described in dealer parts data as a main hydraulic pump. Volvo’s own online catalogue does not return a citable page for 15140666, so the machine list is dealer-established rather than manufacturer-confirmed, and no displacement, pressure or flow figure is published for it here.

Where a two-series listing stops being helpful

Volvo carried the pump train forward from the F series into the G series, so a shared part number is plausible. What does not carry forward automatically is the control setting: pressure cut-in, flow priority and the regulator arrangement were revised on some G-series builds. A pump that is physically identical and set up differently will fit, run, and leave the machine slow to tip. Confirm from the number cast on your pump and the machine serial prefix, not from the model letter alone.

Diagnosis and fitting

  • Judge the pump hot: hoist and tip times lengthen as oil temperature rises.
  • Rule out relief settings and the body holding valve before condemning the pump.
  • Noise under load points at cavitation, so check the suction line and strainer.
  • On fitting, match shaft spline, pilot, flange, port positions and control orientation against the removed pump, prime with clean oil before cranking, change the return filter element, keep the case drain unrestricted to tank, and target ISO 4406 18/16/13.

دليلنا دليل المشتري والمواصفات للمضخات يغطي كيفية مقارنة البديل بالأصل، و قائمة التحقق لإعادة بناء طقم الإحكام covers what a proper rebuild should include.

الطلب

Minimum order one piece. Three to six month warranty on new aftermarket units as stated on your proforma invoice; photographed against your order before the wooden case closes, delivery 5 to 8 working days from payment subject to stock. Related: 15020161 for the E and F series and 17487754 for the G series; this section covers hauler hydraulic pumps.

لا يمكنك العثور على قطعة غيار؟ هل تحتاج إلى شحنها اليوم؟ اسألنا الآن.

شارك طرازك أو رقمك التسلسلي أدناه للحصول على عرض أسعار ثابت، وغالباً ما يتم الإرسال في نفس اليوم.