Hitachi EX200-5 Κύρια Υδραυλική Αντλία – Κινεζική Ανακατασκευασμένη (Συναρμολόγηση Hefei: 9150726 / 9152668)

Περιγραφή

Λεπτομερείς πληροφορίες

1. Βασικά χαρακτηριστικά & οφέλη

• Precision‑remanufactured for Hefei‑assembled EX200‑5 – This twin pump set (9150726 / 9152668) is specifically rebuilt to Hitachi‘s factory specifications for the locally produced (Hefei) EX200‑5 excavator. Every critical component – cylinder block, piston assemblies, valve plate, swashplate, bearings, and seals – is either renewed or replaced with new, high‑quality parts. The result is restored hydraulic performance at a fraction of the cost of a new genuine pump set.

• Original Hitachi tandem axial piston architecture – The two pumps work together as a variable displacement tandem system, powering travel, swing, boom, arm, and bucket circuits independently. This design ensures smooth, coordinated multi‑function operation without internal flow loss – exactly as your EX200‑5 performed when it left the Hefei assembly line.

• Restored 20‑ton class power – After remanufacturing, the pump set delivers a rated working pressure of 31.9 MPa (≈4,630 psi) with intermittent peaks up to 34.3 MPa (≈4,975 psi). Combined flow is approximately 360‑400 L/min at rated engine speed. Your excavator regains full digging force, fast cycle times, responsive swing, and powerful travel.

• Ενσωματωμένος έλεγχος ισχύος με ανίχνευση φορτίου – Το εργοστασιακό σύστημα ελέγχου ισχύος (load-sensing) έχει ανακατασκευαστεί πλήρως. Προσαρμόζει συνεχώς την απόδοση της αντλίας στην πραγματική ζήτηση εργασίας, μειώνοντας την κατανάλωση καυσίμου, αποτρέποντας το σβήσιμο του κινητήρα υπό ξαφνικό φορτίο και παρατείνοντας τη διάρκεια ζωής ολόκληρου του υδραυλικού συστήματος. Η ενσωματωμένη αντλία πιλότου γραναζιών είναι επίσης πλήρως ανακατασκευασμένη.

• Οικονομικά αποδοτική εναλλακτική λύση έναντι νέου γνήσιου – A new Hitachi main pump set for a 20‑ton excavator is a major investment. Our remanufactured 9150726 / 9152668 gives you the same fit, form, and function at a significantly lower price, without sacrificing reliability. Each pump is dyno‑tested before dispatch.

• Άμεση αντικατάσταση με βίδωμα (bolt-on) – Mounting flanges, drive shaft splines, and hydraulic port configurations are restored to original Hefei‑spec Hitachi dimensions. No modifications, no adapters, no fabrication – your mechanic unbolts the old pumps and bolts these in.

• Οπτική επαλήθευση πριν από την αποστολή – We send you clear, high‑resolution photographs of the actual remanufactured units (mounting flanges, splines, port threads, castings, overall condition) before packing. You approve shipment – we never ship blind.

• Γρήγορη παράδοση – 5–8 working days from our Guangzhou warehouse. Monthly supply capacity of 300 sets, available for single‑set or bulk orders.

2. Εφαρμογές

The remanufactured Hitachi 9150726 / 9152668 main pump set is ideal for the Hefei‑built EX200‑5 (20‑ton class) used in demanding job sites:

• Βαριές κατασκευές & υποδομές – Highway excavation, dam building, bridge footings, large‑scale earthmoving. The restored tandem pumps deliver simultaneous boom, arm, and travel power without internal leakage – no power fade, no sluggish response, even on long shifts.

• Λατομεία & αδρανή υλικά – Loading trucks, stockpile management, and material handling in abrasive dust conditions. New bearings, seals, and wear plates ensure the pumps survive where worn units fail. Consistent flow and pressure mean faster cycle times and lower fuel consumption.

• Υποστήριξη εξόρυξης – Site cleanup, road maintenance, drainage works, and equipment pad grading. The load‑sensing control reduces fuel burn during light‑duty cycles, saving money over thousands of operating hours.

• Κατεδάφιση & Επεξεργασία Σκραπ – Shock loads and vibration are routine. Our remanufacturing process replaces all wear components, restoring the pumps‘ ability to withstand harsh, unpredictable conditions.

• Στόλος ενοικίασης εξοπλισμού – 20‑ton excavators are rental workhorses. A remanufactured pump set offers predictable service life (3,000–5,000 hours) at a cost that makes proactive replacement financially sensible – avoiding costly mid‑rental failures, towing bills, and customer complaints.

• Δασοκομία & εκκαθάριση γης – Steep slopes, fallen timber, hidden obstacles. The integral power control prevents engine stall under sudden load spikes, maintaining consistent hydraulic power for saws, grapples, and mulchers.

3. Γιατί να Επιλέξετε Μέρη Hongtengda – Remanufacturing Without Compromise

At Hongtengda Parts, we have been remanufacturing hydraulic pumps for Hitachi excavators since 2001. We know that a main pump failure on your EX200‑5 stops your job site completely. Our remanufacturing process is not a “clean and reseal” – it is a factory‑grade restoration.

Η διαδικασία ανακατασκευής 6 βημάτων μας:

1. Complete disassembly – Each pump is stripped down to individual components: cylinder block, piston assemblies, valve plate, swashplate, bearings, shaft, housing, and control valves.

2. Καθαρισμός και επιθεώρηση ρωγμών – Όλα τα μέρη καθαρίζονται σχολαστικά και ελέγχονται για ρωγμές χρησιμοποιώντας δοκιμή διεισδυτικού υγρού σε κρίσιμα χυτά. Τα μη επισκευάσιμα μέρη απορρίπτονται.

3. – Τα ακόλουθα αντικαθίστανται πάντα με καινούργια, όχι επαναχρησιμοποιημένα: όλες οι τσιμούχες, όλοι οι δακτύλιοι Ο, όλες οι φλάντζες, όλα τα ρουλεμάν κυλίσεων, το πλήρες συγκρότημα εμβόλου/πέδιλου, η πλάκα φθοράς της κυλινδρικής κάννης και η πλάκα βαλβίδας. – All seals, O‑rings, bearings, and gaskets are replaced with new. The cylinder block and valve plate are re‑ground to restore flatness. Piston assemblies are matched as a set and replaced if worn. The swashplate surface is reconditioned.

4. Precision reassembly – Components are reassembled using OEM torque specifications. Clearance tolerances on the cylinder block / valve plate interface are verified.

5. Επικύρωση σε δοκιμαστική βάση υδραυλικών – The completed pump set is mounted to a test stand and run through its full pressure and flow range. We verify operating pressure (up to 31.9 MPa), flow rate (approx. 360‑400 L/min total), case drain leakage, and power control response. A test report is available upon request.

6. Τελικός ποιοτικός έλεγχος και συσκευασία – The pumps are painted, fitted with protective port caps, and packed in a heavy‑duty wooden case for export.

Γιατί η ανακατασκευασμένη αντλία μας υπερέχει έναντι των φθηνότερων “ανακατασκευασμένων” μονάδων:

• Νέα ρουλεμάν και στεγανοποιήσεις – Πολλοί οικονομικοί ανακατασκευαστές επαναχρησιμοποιούν παλιά ρουλεμάν για να εξοικονομήσουν κόστος. Εμείς όχι. Όλα τα περιστρεφόμενα εξαρτήματα λαμβάνουν νέα ρουλεμάν – ο πιο σημαντικός μεμονωμένος παράγοντας για τη μακροζωία της αντλίας.

• Επιφάνειες φθοράς με λείανση ακριβείας – Το μπλοκ κυλίνδρ.

• Full test report – Upon request, we provide a test report showing pressure, flow, case drain, and temperature measurements. You see the data before you buy.

Τι δεν αγοράζετε: A used pump with new paint and a set of O‑rings. Our remanufactured pump set is restored to meet or exceed OEM performance standards – at a price that makes sense for your older EX200‑5.

• 25+ χρόνια εμπ – Founded in 2001, we have remanufactured thousands of pumps for Hitachi, Caterpillar, Komatsu, Kobelco, Volvo, SANY, and many other brands.

• 90% διαθεσιμότητα στο απόθεμα – 9150726 / 9152668 pump sets are in stock as remanufactured units, ready for dispatch from our Guangzhou warehouse.

• Αποστολή εντός 24 ωρών – Από το κέντρο μας στην Guangzhou στον μεταφορέα σας σε 1 ημέρα· οι διεθνείς παραγγελίες αποστέλλονται εντός 24 ωρών.

• Οπτική επαλήθευση πριν από την αποστολή – We never ship a pump blind. You receive clear photos of the actual units before packing – you approve, we ship.

• Τεχνική υποστήριξη – Send us your EX200‑5 (Hefei) machine serial number and photos of the old pumps. We confirm compatibility and provide installation guidance within 2 hours.

Send us your Hefei‑built EX200‑5 machine serial number and photos of the old pumps – we will verify fitment, provide a quote, and document our pre‑shipment inspection within 24 hours.

Critical installation tip for the 9150726 / 9152668 remanufactured pump set:
– The η γραμμή αποστράγγισης περιβλήματος on each pump must be clear and unrestricted. A blocked case drain will blow the shaft seal instantly on first startup.
– Before installing the remanufactured pumps, flush the entire hydraulic system and replace all filters. Contaminants from the failed pumps will destroy a remanufactured unit just as quickly as a new one.
– Use new O‑rings and sealing washers on every hydraulic connection. Reused seals guarantee leaks.
– After installation, run the engine at low idle for 2–3 minutes with the pumps in neutral, then slowly cycle each function (boom, arm, bucket, swing, travel) to purge air from the system.
– Check pump alignment with the engine flywheel housing – misalignment causes premature bearing failure and shaft seal leakage.

Σημείωση εγγύησης: Warranty period is 3 to 6 months depending on product details. We do not provide warranty service for original used or remanufactured parts. Our value is delivered up front: careful remanufacturing, thorough testing, and pre‑shipment visual verification. For customers who require a warranty‑covered option, we can quote new aftermarket units – ask our sales team.

The main hydraulic pump set is the heart of your EX200‑5‘s hydraulic system. Our remanufactured 9150726 / 9152668 gives you restored 20‑ton class performance at a cost that keeps your budget intact – not with shortcuts, but with a genuine factory‑grade restoration. Send us your Hefei EX200‑5 machine serial number – we will confirm compatibility and provide a quote within 24 hours.